Production Aston Martin Valkyrie will be even wilder than concept

Jaws all over the world dropped last summer with the reveal of a concept showcasing an early design for Aston Martin’s new Valkyrie hypercar being developed in partnership with the Red Bull Racing Formula One team.

AFF Suzuki Cup 2018: Anything is possible in football, says Malaysia goalkeeper Farizal Marlias
Friday December 14, 2018

Malaysia goalkeeper Farizal Marlias has said that anything is possible in football ahead of his side's AFF Suzuki Cup 2018 final second leg against Vietnam. The Harimau Malaya travel to Hanoi for the second instalment of the final after the 2-2 draw in the first leg at Kuala Lumpur. With two away goals, the Golden Dragons are certainly […]

The post AFF Suzuki Cup 2018: Anything is possible in football, says Malaysia goalkeeper Farizal Marlias appeared first on 188bet.

However, opposite to what’s usually the case in the auto industry, the production version of the Valkyrie is shaping up to be an even wilder car than the concept.

Cristiano Ronaldo accepts tax fraud charges, set to appear in court
Friday December 14, 2018

Cristiano Ronaldo might be known for his on-field exploits but it is his off-field ones which have landed him in trouble. The Portuguese footballer has pleaded guilty in a tax fraud case for his misdemeanours in Spain, and is set to appear in front of a judge.  It is not entirely new for players to […]

The post Cristiano Ronaldo accepts tax fraud charges, set to appear in court appeared first on 188bet.

Aston Martin late on Tuesday revealed a near production-ready example of the Valkyrie, and it’s got even more fins, air channels and aerodynamically shaped surfaces than the concept. According to Aston Martin, the design shown here is 95 percent complete. Some elements will change as the design team, led by Red Bull’s expert aerodynamicist, Adrian Newey, attempts to eke out as much downforce as possible.

Thursday January 01, 1970

Compared to the concept, new air channels designed to add to the overall downforce of the car have been dug into the front wheel arches. They also double as Aston Martin’s famous side strakes—a clear case of form following function. The wheels also feature a flat surface designed to reduce air turbulence. Aston Martin says this controversial design will be an available feature, however.

Aston Martin Valkyrie in near-production formAston Martin Valkyrie in near-production form

The teardrop-shaped cabin’s upper surfaces and lower tub contours remain the same as on the concept. They follow the envelope of space available between the massive Venturi tunnels that run the length of the car either side of the cabin’s floor. These help to generate most of the downforce, allowing the upper surfaces to be devoid of additional aero elements and thus retain their clean, almost sensual look.

The rear of the Valkyrie is where most of the changes have occurred. The single exhaust exit of the concept has been replaced by a twin-exit design while the trailing edge of the Venture tunnels now take on a more curved appearance. This curved theme is carried over to the rear wing which is now just a single arch. Also fitted to the car at both ends are the production lights which are full LED units.

In case you’ve forgotten, the Valkyrie will be powered by a mid-mounted 6.5-liter V-12 working in conjunction with a KERS-style hybrid system. The V-12 alone is expected to produce 1,000 hp, making it the most powerful naturally aspirated engine of any production car. An additional 130 hp is expected to be added by the hybrid system’s electric motor. Both power sources will drive the rear wheels only, via a 7-speed transmission of undisclosed type.

Amazingly, we’ve heard that the power-to-weight ratio could exceed 1:1, as measured in horsepower per kilogram. Assuming the 1,130-hp output is accurate, the Valkyrie would tip the scales at sub-Mazda MX-5 Miata levels! Weight-saving measures extend right to the Aston Martin badge which is just 70 microns thick, or about 30 percent thinner than a human hair. The aluminum piece, created using a special chemical etching process, is 99.4 per cent lighter than the regular enamel badge used on Aston Martin cars

Tag: ,